Haiyuan is a custom blanket manufacturer and home textile supplier since 2003.
Haiyuan is the best blanket factory and home textile products supplier since 2003
Haiyuan is the best blanket factory and home textile products supplier since 2003
Haiyuan is the best blanket factory and home textile products supplier since 2003
Haiyuan is the best blanket factory and home textile products supplier since 2003
Frame @2x for custom blankets
Search
Close this search box.
Industry News
October 15, 2026
Industry News

How to Sublimate a Blanket: Blanks, Settings and Finishing

Learning how to sublimate a blanket starts with fleece containing at least 50% polyester, a printed design placed face down, and a controlled heat-press sample. One published fleece method uses a five-second pre-press followed by about 385°F (195°C) for 30–45 seconds at medium pressure, but these are starting instructions for that method rather than universal settings.

How to Sublimate a Blanket Step by Step

  1. Select fleece containing at least 50% polyester.
  2. Place the printed design face down on the blanket.
  3. Pre-press for about five seconds.
  4. Press near 385°F (195°C) for 30–45 seconds at medium pressure.
  5. Let the blanket cool before removing the paper.
  6. Inspect the sample before approving production.

Steps one through five follow Puffy’s fleece sublimation guide, which says the exact temperature may vary according to the heat press. The final inspection is a proposed production-control step, not an instruction documented in that guide.

When comparing blanks while learning blank blanket range, approve the exact construction intended for the order. Approval of one fleece shouldn’t be transferred automatically to another weight, pile, blend, backing, or finish.

The Blank Is What Takes the Ink

Puffy’s guide recommends fleece containing at least 50% polyester. It says a greater polyester percentage should produce a brighter, clearer image, presenting this as an expected direction rather than a guaranteed result for every blank.

A 50/50 cotton-polyester fleece meets the guide’s minimum recommendation. Based on the same qualified guidance, a higher-polyester fleece is the more promising sample when photo clarity and brightness are priorities.

For wholesale specifications, record the fiber content of the surface being printed. Treating different weights, piles, blends, backings, and finishes as separate approval items is a proposed purchasing control rather than a technical setting established by the cited guide.

Compare Blanket Press Settings

The documented evidence supports one fleece starting method. It doesn’t justify assigning different temperatures or times according to blanket weight or pile.

Fleece variable or step Documented guidance Scope
50% polyester fleece The guide recommends fleece with at least 50% polyester Minimum recommended polyester content, not a guaranteed result
Higher-polyester fleece Greater polyester content should produce brighter, clearer images Expected direction, not a measured guarantee
Pre-press About five seconds to address moisture and wrinkles Part of the guide’s fleece method
Main press Around 385°F (195°C), 30–45 seconds, medium pressure Starting range; the guide says temperature can vary by press
Paper removal Let the blanket cool before removing the paper Part of the guide’s fleece method

For production approval, a proposed control method is to identify the exact blank, use the documented range for the first sample, and record each later adjustment separately. Keep the artwork and blank construction unchanged while comparing settings.

Cool, Peel, and Finish the Blanket

For the documented fleece method, let the blanket cool before removing the transfer paper. The supplied evidence supports cool removal for this method; it doesn’t establish a hot-peel process for other papers or materials.

Puffy’s guide recommends washing the finished blanket on a gentle cycle with mild detergent, followed by air drying or low-temperature drying. For a commercial order, applying that care process to an approved sample before finalizing the care instructions is a separate quality-control recommendation.

What a Blank Supplier Watches on the Same Job

Print shops judge a blank by how the transfer lands. We judge it a step earlier, at the cloth.

Whiteness sets the ceiling for every colour above it. An optical-white polyester face returns the print as designed, while an off-white or slightly grey lot pulls reds toward brick and blues toward slate across the whole run.

Pile evenness decides how fine detail survives. A flat brushed face holds small type and sharp edges, and a deeper plush face spreads them slightly, which suits photographic art more than hairline text.

Edge construction decides what the press does to the blank. Polyester thread in an overlocked or stitched hem takes press heat without shrinking away from the seam, and that is what keeps a 50×60 inch panel square after pressing.

A sherpa-backed blank behaves differently again, because the bonded second layer carries heat into the press cycle and holds it longer on the way out.

None of this appears on a spec sheet as a single number. It shows up in a sample pressed on the buyer’s own machine, with the buyer’s own paper and ink.

Approve the Production Sample

A proposed sample record should identify the blank construction, printed side, fiber content, weight, pile, artwork revision, finished image size, printer, ink, paper, press, temperature, time, pressure, pre-press, and removal timing. Keep the approved sample with that record rather than treating the guide’s starting figures as approval for every construction.

Before continuing a batch, compare the first completed piece with the approved sample after both have cooled. Check orientation, margins, overall image appearance, and consistency with the agreed care test.

FAQ

Is sublimation hard to learn?

The documented fleece sequence is straightforward, but consistent production still requires an approved sample of the exact blanket. The guide’s settings are a starting method rather than a guarantee.

Which material is best for photo blankets?

The cited guide recommends fleece with at least 50% polyester and says greater polyester content should produce brighter, clearer images. That makes higher-polyester fleece the stronger candidate to test for detailed photos, not a guaranteed best option for every product.

Can I sublimate 50/50 cotton-polyester?

A 50/50 fleece meets the guide’s minimum polyester recommendation and can be tested. The guide says higher polyester content should give brighter, clearer results, so approve the 50/50 blank from a physical sample.

Do you peel sublimation paper hot or cold?

The documented fleece method calls for letting the blanket cool before removing the paper. This evidence doesn’t establish the correct removal method for other material and transfer combinations.

For an OEM or ODM sample brief, specify fiber content, size, fabric weight, pile, artwork dimensions, press method, packaging, and care requirements. You can review HY Blankets’ white polyester blanket blanks as a sourcing reference, then approve the artwork and press method on the exact production construction before confirming a bulk order.

leave a comment
Your email address will not be published. Required fields are marked *
Please enable JavaScript in your browser to complete this form.
Popular Post